Plumbing 101: Tips for Bathtub Installation
Plumbing 101: Tips for Bathtub Installation
Blog Article
The article in the next paragraphs pertaining to Tools You Need to Install a New Bathtub is fairly remarkable. Read on and draw your own conclusions.
Mounting a bathtub isn't specifically brain surgery, yet it does require strong plumbing, woodworking, as well as often, tiling abilities. Changing an old bath tub with a new one is likewise a reasonably hard project. If the old tub is easily obtainable, the task can relocate quickly; if you have to open a wall surface to eliminate the old bathtub as well as place the new bath tub, the task is much harder. In either instance, the task is within a house handyman's abilities, although you will certainly require a helper to vacate the old bathtub as well as embeded in the brand-new one. Make certain you have actually qualified on your own for the job and are comfortable trying it. As opposed to employing a contractor to take control of a halfway-completed project, it is far better to think about employing one before you start. Possibilities are you may need an expert plumber to make tube connections.
This write-up will certainly aid you mount a new bath tub in your restroom if you have already gotten a new bathtub and also don't need to alter the plan of your previous water supply pipes.
Your devices and also product list should make up the following:
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installation, then the first thing you ought to do is disconnect the water system. After doing so, turn on the taps to drain any type of water remaining in the system. The process of getting rid of the existing taps can be fairly problematic because of the restricted access that is typically the situation.
Use a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipes to the faucets. Have a cloth prepared for the remaining water that will come from the pipes. As soon as the supply pipes have actually been eliminated, make use of the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from transforming throughout this procedure. Once the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing compound.
Before moving on to fit the brand-new faucets, compare the pipe connections on the old taps to the new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will certainly need a plastic adapter to stop damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end provides a connection to the current supply pipelines.
If you require to fit a monobloc, then you will require lowering couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the installing hole in the bath/basin making sure that the washing machines are in area between the tap as well as the sink. Secure the faucet in place with the supplier supplied backnut. When the faucet is securely in place, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with typical tap ports. The previous kind must be attached to the tap finishes first, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.
Installing the Tub
Using both wooden boards under its feet, position the bath tub in the required position. The wooden boards are handy in uniformly spreading out the weight of the bath tub over the area of the boards rather than focusing all the weight onto 4 little points.
The next objective is to ensure that the bath tub is leveled all round. This can be achieved by inspecting the level as well as changing the feet on the bath tub till the spirit level reads degree.
To set up taps, fit the bottom of the furthest adaptable faucet adapter to the proper supply pipeline by making a compression sign up with; after that do the exact same for the other faucet.
Switch on the water system as well as inspect all joints and brand-new pipework for leaks as well as tighten them if essential. Fill the bathtub as well as likewise inspect the overflow electrical outlet and also the regular electrical outlet for leakages.
Finally, take care of the bath paneling as defined in the producer's instruction manual. Tiling as well as securing around the bathtub should wait up until the bath tub has been used a minimum of when as this will certainly resolve it right into its last setting.
Planning for the Setup
First of all, the supporting frame provided with the bath must be fitted (if required) according to the producer's instructions. Next, fit the taps or mixer to the tub. When suitable the tap block, it is essential to make certain that if the tap comes with a plastic washer, it is fitted between the bath and the faucets. On a plastic bathroom, it is also sensible to fit a sustaining plate under the faucets system to avoid stress on the bath tub.
Fit the adaptable faucet adapters to the bottom of both taps using 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet through the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Make certain you make use of every one of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom must now be ready to be suited its final setting.
Tiling Around the Bath tub
In the area where the bathroom satisfies the ceramic tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to crack an inflexible seal, causing the water to permeate the wall surface in between the bathroom as well as the tiling, bring about issues with moisture and possible leaks to the ceiling below.
You can select from a variety of coloured sealants to blend in your fixtures as well as fittings. They are marketed in tubes and cartridges, and also are capable of securing gaps approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of drenched paper or soft rope. Remember to always fill up the tub with water before securing, to enable the motion experienced when the tub remains in use. The sealer can fracture relatively early if you do not consider this motion prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also conveniently offered on the market. It is a good idea to fit the tiles utilizing water-resistant or water resistant adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was made aware of that write-up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround through an acquaintance on another blog. Kindly set aside a second to distribute this write-up if you appreciated it. Thanks a bunch for your time. Come back soon.
Quality-driven emergency plumbing solutions. Report this page